Arlington, Tarrant County
Broken Spring Replacement in Arlington, TX
A spring replacement is a bounded job with a known price once we see the door. What costs real money is running the door after the spring broke. That puts the whole weight on the opener, the shaft and the cables, and in Arlington a spring call turns into a spring, gear and cable call.
- Emergency and same-day repairs
- 5.0 from 10 reviews
- Upfront pricing, no hidden fees
- Free estimates
Why this is the job we tell people to stay off of
The broken spring is not the danger. It already let go. The danger is everything else still loaded. On a two spring door, the other spring is still fully wound. Both bottom brackets are still under the full pull of that counterbalance, which is exactly why the factory puts a warning label on them. Winding a torsion spring takes steel winding bars seated in the cone holes. Wrong size bar, loose set screw, or a hand slipping, and the bar comes out at speed with hundreds of pounds behind it. Emergency rooms see these. They are hand, wrist, face and teeth injuries. People use screwdrivers and rebar because that is what is in the garage, and that is how most of it happens.
Torsion and extension springs are two different systems
Torsion springs sit on a shaft above the door. That is what most doors built in the last few decades use. Extension springs run along the horizontal tracks on both sides, stretch when the door closes, and pull back to help lift it. Plenty of older and lighter doors still have them. Here is the part that matters: an extension spring needs a safety cable run through the middle of it and anchored at both ends. Without that cable, a spring that snaps becomes a length of steel whipping across your garage. If your door has extension springs and no safety cables, we will put them in. They are cheap.
Sizing is measuring, not eyeballing
A torsion spring is defined by four things: wire diameter, inside diameter, length, and which way it winds. Those decide how much torque you get per turn. Picking the replacement means knowing what the door weighs, either by putting it on a scale with the springs off or by calculating from the panel construction and hardware. Too light a spring and the door stays heavy at the floor and burns through cycles fast. Too heavy and the door wants to fly open and the opener fights it all the way down. Both feel more or less fine on day one. Both cut the life of everything they are bolted to.
Broken Spring Replacement for Arlington homes
A huge 1960s-80s middle band of attached two-car garages sits between older north Arlington singles and newer south Arlington three-car homes, making 16x7 doors by far the most requested size.
We cover ZIP codes 76001, 76006, 76010, 76012, 76013 and 76017.
Regular calls come from Viridian, Dalworthington Gardens area and Interlochen.
If you are near Globe Life Field, you are well inside our route.
Arlington sits in Tarrant County with a population of about 403,672.
Please do not attempt this one yourself
That spring is still loaded even with the door down. People get badly hurt trying to unwind one with the wrong tools. Leave the door shut, do not pull the release, and call us.
What you are probably seeing
- A loud bang from the garage, and the door worked fine right up until then.
- A two to three inch gap in the coil of the spring above the door.
- Opener strains, moves the door a few inches, then stops or reverses.
- Door is extremely heavy by hand and will not stay up.
- Door goes up crooked with one side behind the other.
Arlington service
Call (214) 831-2545 or request a visit.
The visit
How a Arlington call runs
Confirm it and secure the door
We find which spring broke, check whether the other one is still loaded, and clamp or block the door so it cannot move while we work. Opener stays disconnected the whole time.
Measure the door and the old springs
Wire diameter, inside diameter, length and wind direction come off the existing springs, and we establish what the door weighs. That decides the replacement. Not a visual match.
Unwind and strip it
Any leftover tension comes off with proper winding bars, cables come off the drums, old springs come off the shaft. We check the bearings, drums and shaft while we can actually see them.
New pair, wound to the right turn count
Both springs go on. Cables get set in the drums with equal tension so the door lifts square. Springs get wound to the turns this door needs, not to a default number.
Balance by hand, then reset the opener
Door gets lifted by hand and checked at several heights to make sure it holds position. Then the opener goes back on, travel and force get reset, and we test the safety reverse.
On the job
Broken Spring Replacement in the field
Questions
Broken Spring Replacement in Arlington
Can I replace a torsion spring myself?
No. That is the one flat no on this whole site. It takes correctly sized steel winding bars, properly seated set screws, and a stance that keeps your body out of the arc of those bars. Improvised tools slipping under that kind of torque send people to the emergency room every year. Almost everything else on a garage door is fair game for a handy person. This is not.
Why do both springs have to go?
Same install date, same cycle count, so the second one is close behind the first. And springs get sized as a pair against the door weight, so a new one next to an old one never balances the door right through its travel. Doing it once costs less than doing it twice.
Did I break it?
No. Springs fail from metal fatigue after a counted number of cycles, and they usually go on a cold morning because the steel is less forgiving then. The two things that actually shorten spring life are a spring undersized for the door at install and rust pitting on the coil. Neither one is about how you use the door.
Should the cables be done at the same time?
Only if they need it, and we will show you. If the cable is fraying at the drum or at the bottom bracket, do it now, because the labor overlaps almost completely and you save a whole visit. If the cables are clean, leave them alone. A spring breaking does not damage a good cable.
Does a broken spring wreck the opener?
Running the door on it will, given enough tries. The opener suddenly has to move the full weight, and what gives out is the drive gear, the trolley, the arm, or the top panel where the arm attaches. One or two presses before you figured out what happened is usually harmless. Twenty is not.
Talk to a technician now
Broken Spring Replacement in Arlington and across Tarrant County.