Benbrook, Tarrant County
Broken Spring Replacement in Benbrook, TX
Most spring jobs in Benbrook are done within an hour to ninety minutes of us pulling up. The truck carries the common wire sizes and lengths. We leave with the door balancing by hand and the opener reset to the fixed door instead of the broken one.
- Emergency and same-day repairs
- 5.0 from 10 reviews
- Upfront pricing, no hidden fees
- Free estimates
What the spring is actually doing up there
The torsion spring sits on a steel shaft above the opening. When it gets installed, it gets wound a set number of turns, usually around seven and a half on a seven foot door. That twist is stored energy. Cables run from drums on each end of the shaft down to brackets at the bottom corners of the door. Closing the door winds the spring tighter. Opening it lets the spring unwind and pull those cables. The whole design is a trade: the spring's torque cancels out the door's weight. That is why a 200 pound door lifts with about ten pounds of hand effort when everything is right.
Both springs get replaced, not just the broken one
Both springs went on the same day and have taken the exact same number of cycles. When one hits the end, the other is right behind it. Beyond that, springs get sized as a matched pair against the door weight, so a new one working next to a fatigued one puts uneven torque across the shaft and the door never balances properly through its travel. Two service calls also cost more than one. This is not an upsell, it is the reason you are not calling us again in four months.
Sizing is measuring, not eyeballing
A torsion spring is defined by four things: wire diameter, inside diameter, length, and which way it winds. Those decide how much torque you get per turn. Picking the replacement means knowing what the door weighs, either by putting it on a scale with the springs off or by calculating from the panel construction and hardware. Too light a spring and the door stays heavy at the floor and burns through cycles fast. Too heavy and the door wants to fly open and the opener fights it all the way down. Both feel more or less fine on day one. Both cut the life of everything they are bolted to.
Broken Spring Replacement for Benbrook homes
Hilly limestone terrain around Benbrook Lake means split-level and downslope garages are common, and rock-cut driveways put uneven load on tracks compared with flatter suburbs.
Those ZIP codes are ours: 76126, 76116 and 76132.
We are in Whitestone Ranch, Timber Creek and Ridgeview most weeks.
If you are near Benbrook Stables, you are well inside our route.
Benbrook is a Tarrant County community of roughly 24,542.
Please do not attempt this one yourself
That spring is still loaded even with the door down. People get badly hurt trying to unwind one with the wrong tools. Leave the door shut, do not pull the release, and call us.
What you are probably seeing
- Opener strains, moves the door a few inches, then stops or reverses.
- Door is extremely heavy by hand and will not stay up.
- Door goes up crooked with one side behind the other.
- Top panel flexes or bends when the opener pulls on it.
- Cables have gone slack or jumped off the drums.
Benbrook service
Call (214) 831-2545 or request a visit.
The visit
How a Benbrook call runs
Confirm it and secure the door
We find which spring broke, check whether the other one is still loaded, and clamp or block the door so it cannot move while we work. Opener stays disconnected the whole time.
Measure the door and the old springs
Wire diameter, inside diameter, length and wind direction come off the existing springs, and we establish what the door weighs. That decides the replacement. Not a visual match.
Unwind and strip it
Any leftover tension comes off with proper winding bars, cables come off the drums, old springs come off the shaft. We check the bearings, drums and shaft while we can actually see them.
New pair, wound to the right turn count
Both springs go on. Cables get set in the drums with equal tension so the door lifts square. Springs get wound to the turns this door needs, not to a default number.
Balance by hand, then reset the opener
Door gets lifted by hand and checked at several heights to make sure it holds position. Then the opener goes back on, travel and force get reset, and we test the safety reverse.
On the job
Broken Spring Replacement in the field
Questions
Broken Spring Replacement in Benbrook
Why do both springs have to go?
Same install date, same cycle count, so the second one is close behind the first. And springs get sized as a pair against the door weight, so a new one next to an old one never balances the door right through its travel. Doing it once costs less than doing it twice.
How long will the new springs last?
Take the cycle rating and divide by how many times a day you open the door. A standard 10,000 cycle spring is four to five years at six openings a day, or about fourteen years at two. If your house is on the heavy end, ask about high cycle springs at 20,000 or more. The price difference is small next to a second replacement.
Can I get my car out before you arrive?
Sometimes, carefully, with help. With the opener released the door weighs everything it weighs, often over 200 pounds on a double. Two adults can usually manage it. Block it open with something solid, never with a person holding it, while the car comes out. Do not run the opener, because that is how a spring job turns into a spring, cable and opener job.
Should the cables be done at the same time?
Only if they need it, and we will show you. If the cable is fraying at the drum or at the bottom bracket, do it now, because the labor overlaps almost completely and you save a whole visit. If the cables are clean, leave them alone. A spring breaking does not damage a good cable.
Does a broken spring wreck the opener?
Running the door on it will, given enough tries. The opener suddenly has to move the full weight, and what gives out is the drive gear, the trolley, the arm, or the top panel where the arm attaches. One or two presses before you figured out what happened is usually harmless. Twenty is not.
Book a visit that fits your day
Broken Spring Replacement in Benbrook and across Tarrant County.