Burleson, Johnson County
Broken Spring Replacement in Burleson, TX
We look for the gap first. A broken torsion spring has a clean two or three inch separation somewhere along the coil and the halves sit apart on the shaft. Then we measure wire size, inside diameter and length, check it against the door weight, and show you those numbers in Burleson before anything goes on.
- Emergency and same-day repairs
- 5.0 from 10 reviews
- Upfront pricing, no hidden fees
- Free estimates
What the spring is actually doing up there
The torsion spring sits on a steel shaft above the opening. When it gets installed, it gets wound a set number of turns, usually around seven and a half on a seven foot door. That twist is stored energy. Cables run from drums on each end of the shaft down to brackets at the bottom corners of the door. Closing the door winds the spring tighter. Opening it lets the spring unwind and pull those cables. The whole design is a trade: the spring's torque cancels out the door's weight. That is why a 200 pound door lifts with about ten pounds of hand effort when everything is right.
Why this is the job we tell people to stay off of
The broken spring is not the danger. It already let go. The danger is everything else still loaded. On a two spring door, the other spring is still fully wound. Both bottom brackets are still under the full pull of that counterbalance, which is exactly why the factory puts a warning label on them. Winding a torsion spring takes steel winding bars seated in the cone holes. Wrong size bar, loose set screw, or a hand slipping, and the bar comes out at speed with hundreds of pounds behind it. Emergency rooms see these. They are hand, wrist, face and teeth injuries. People use screwdrivers and rebar because that is what is in the garage, and that is how most of it happens.
Sizing is measuring, not eyeballing
A torsion spring is defined by four things: wire diameter, inside diameter, length, and which way it winds. Those decide how much torque you get per turn. Picking the replacement means knowing what the door weighs, either by putting it on a scale with the springs off or by calculating from the panel construction and hardware. Too light a spring and the door stays heavy at the floor and burns through cycles fast. Too heavy and the door wants to fly open and the opener fights it all the way down. Both feel more or less fine on day one. Both cut the life of everything they are bolted to.
Broken Spring Replacement for Burleson homes
One of the fastest-growing cities on the Fort Worth south side, with an Old Town core of pre-war homes and detached garages ringed by 2000s subdivisions of attached doubles.
We cover ZIP code 76028.
We are in Mountain Valley, Elk Ridge and Old Town Burleson most weeks.
If you are near Bailey Lake, you are well inside our route.
Burleson is a Johnson County community of roughly 56,253.
Please do not attempt this one yourself
That spring is still loaded even with the door down. People get badly hurt trying to unwind one with the wrong tools. Leave the door shut, do not pull the release, and call us.
What you are probably seeing
- Door goes up crooked with one side behind the other.
- Top panel flexes or bends when the opener pulls on it.
- Cables have gone slack or jumped off the drums.
- Gaps between coils on a spring that has not broken yet, or rust pits in the coil.
- A loud bang from the garage, and the door worked fine right up until then.
Burleson service
Call (214) 831-2545 or request a visit.
The visit
How a Burleson call runs
Confirm it and secure the door
We find which spring broke, check whether the other one is still loaded, and clamp or block the door so it cannot move while we work. Opener stays disconnected the whole time.
Measure the door and the old springs
Wire diameter, inside diameter, length and wind direction come off the existing springs, and we establish what the door weighs. That decides the replacement. Not a visual match.
Unwind and strip it
Any leftover tension comes off with proper winding bars, cables come off the drums, old springs come off the shaft. We check the bearings, drums and shaft while we can actually see them.
New pair, wound to the right turn count
Both springs go on. Cables get set in the drums with equal tension so the door lifts square. Springs get wound to the turns this door needs, not to a default number.
Balance by hand, then reset the opener
Door gets lifted by hand and checked at several heights to make sure it holds position. Then the opener goes back on, travel and force get reset, and we test the safety reverse.
On the job
Broken Spring Replacement in the field
Questions
Broken Spring Replacement in Burleson
Can I replace a torsion spring myself?
No. That is the one flat no on this whole site. It takes correctly sized steel winding bars, properly seated set screws, and a stance that keeps your body out of the arc of those bars. Improvised tools slipping under that kind of torque send people to the emergency room every year. Almost everything else on a garage door is fair game for a handy person. This is not.
Can I get my car out before you arrive?
Sometimes, carefully, with help. With the opener released the door weighs everything it weighs, often over 200 pounds on a double. Two adults can usually manage it. Block it open with something solid, never with a person holding it, while the car comes out. Do not run the opener, because that is how a spring job turns into a spring, cable and opener job.
Did I break it?
No. Springs fail from metal fatigue after a counted number of cycles, and they usually go on a cold morning because the steel is less forgiving then. The two things that actually shorten spring life are a spring undersized for the door at install and rust pitting on the coil. Neither one is about how you use the door.
Should the cables be done at the same time?
Only if they need it, and we will show you. If the cable is fraying at the drum or at the bottom bracket, do it now, because the labor overlaps almost completely and you save a whole visit. If the cables are clean, leave them alone. A spring breaking does not damage a good cable.
Do you have springs on the truck?
The common residential wire sizes and lengths, yes, so most jobs get done on the first visit. Unusual sizes, very heavy custom doors, and some high cycle setups occasionally have to be ordered. If yours is one of those, you hear it at the diagnosis, not later.
Talk to a technician now
Broken Spring Replacement in Burleson and across Johnson County.