Pelican Bay, Tarrant County
New Garage Door Installation in Pelican Bay, TX
Most doors we replace in Pelican Bay are not worn out. They are underbuilt. Thin single layer steel with no strut across the top flexes a little every lift, and that flex works the hinges loose, wears the top rollers, and eventually cracks the panel where the opener pulls on it.
- Emergency and same-day repairs
- 5.0 from 10 reviews
- Upfront pricing, no hidden fees
- Free estimates
Insulation, and what it buys you in Texas
Polystyrene board gets cut and fitted into the panel and lands somewhere around R-6 to R-9. Injected polyurethane foam expands and bonds both skins together, which is why those doors hit R-12 to R-18 and are stiffer at the same time. Around here the summer case is much stronger than the winter one. A garage that stays twenty degrees cooler in August is a garage you can use. And if there is a bedroom or a bonus room over it, the insulated door pulls real load off that room's air conditioning all season.
The springs have to be sized for the new door, not the old one
Springs match weight, and a new door rarely weighs what the old one did. An insulated three layer door can be eighty pounds heavier than the single layer it replaces. Reuse the old springs on that and the counterbalance never balances, the opener carries the difference every cycle, and the springs burn through their cycle life early. We weigh the assembled door or calculate it from panel construction and hardware, then pick wire size, inside diameter and length to match. It is the part of the install nobody sees and it decides how the door feels for the next ten years.
The stuff people forget to ask about
The bottom seal has to match your slab, and slabs around here are rarely flat, so an oversize seal may be needed to close a gap on one end without buckling on the other. Weatherstrip on the jambs and header keeps out dust and sideways rain. Track has to be lagged into solid framing, and rotten jamb wood gets replaced before the door goes on it. Rollers that come with an entry level door are often steel with open bearings. Upgrading to sealed nylon at install is cheap and it is the single biggest difference in how quiet the door is.
New Garage Door Installation for Pelican Bay homes
A compact community beside Eagle Mountain Lake with a high share of manufactured and small frame homes, so carports and detached single-bay garages outnumber attached doubles.
If your address falls in 76020, you are on our board.
Anywhere around Pelican Bay City Hall is a short run for us.
Pelican Bay is a Tarrant County community of roughly 2,674.
What you are probably seeing
- The door visibly flexes in the middle as it starts to lift.
- Hinges have torn out and the steel around them is cracked.
- The garage is unusable in summer and the door is the biggest uninsulated surface in it.
- It is still a one piece tilt up door, which limits parts and eats headroom.
- Two years of repair bills are adding up to a real chunk of a new door.
Pelican Bay service
Call (214) 831-2545 or request a visit.
The visit
How a Pelican Bay call runs
Measure and spec
Opening, headroom, backroom, side room, jamb and header condition, and whether the existing opener is worth keeping. You get options at more than one construction level with the tradeoffs explained, not one recommended package.
Order with a real lead time
Stock sizes and finishes move quickly. Custom widths, specialty finishes and window inserts take longer, and you get that number before the deposit rather than after.
Take the old one down safely
Springs unwound with winding bars, cables released from the drums, sections down from the top in order. Old track, hardware and springs go with us.
Install and set the counterbalance
Sections stack from the bottom with hinges and rollers set as they go, track gets lagged into solid framing and aligned, then shaft, drums and springs go in and get wound to the turn count the finished door weight calls for.
Commission it
Door gets run by hand to confirm balance, opener travel and force get set, sensors get mounted within six inches of the floor, the auto reverse gets tested against an obstruction, and we walk you through the manual release before we leave.
On the job
New Garage Door Installation in the field
Questions
New Garage Door Installation in Pelican Bay
Can I keep my existing opener?
Usually, if it is mechanically sound and has working photo eyes. Two things to watch. A much heavier insulated door asks more of an older half horsepower unit. And the opener arm needs a properly reinforced top section, which may mean adding a strut. If the opener is old enough to have no photo eyes, replace it regardless of the door.
How much headroom do I need?
About twelve inches above the opening for standard track. Less than that and you are looking at a low headroom conversion with double track and split drums, which works in roughly four and a half to six inches, or a wall mount opener that gets rid of the ceiling rail entirely. Both cost more, so measure before you pick a setup.
Do you replace the track too?
Yes, always. Reusing old track on a new door is false economy. Vertical track carries the door's alignment, old track is worn where the rollers ride and usually a little out of plumb, and any of that transfers straight into your new panels and rollers.
What is the warranty?
It comes from the manufacturer and it varies a lot by model on panels, hardware, springs and finish. We hand you the written terms for the specific door you pick instead of summarizing it verbally, because the actual limits are in that document.
Can I install a door myself?
Stacking sections and hanging track is doable if you build things. Winding the torsion springs is not, and that is not us protecting a sale. Winding bars under several hundred pounds of torque break arms and jaws when they slip. If you install it yourself, hire out the spring work.
Get it fixed, not patched
New Garage Door Installation in Pelican Bay and across Tarrant County.