A LIFT GARAGE DOOR (214) 831-2545 Book Online
Newly installed white ribbed sectional door seen from inside a steel building, its galvanised struts, torsion spring, cable drums and red emergency release cord all visible against the metal wall.

River Oaks, Tarrant County

Broken Spring Replacement in River Oaks, TX

It sounds like a gunshot in the garage. Then the door will not lift. That is a torsion spring letting go of everything it was holding, all at once. It is the single most common thing we replace in River Oaks.

  • Emergency and same-day repairs
  • 5.0 from 10 reviews
  • Upfront pricing, no hidden fees
  • Free estimates

Why this is the job we tell people to stay off of

The broken spring is not the danger. It already let go. The danger is everything else still loaded. On a two spring door, the other spring is still fully wound. Both bottom brackets are still under the full pull of that counterbalance, which is exactly why the factory puts a warning label on them. Winding a torsion spring takes steel winding bars seated in the cone holes. Wrong size bar, loose set screw, or a hand slipping, and the bar comes out at speed with hundreds of pounds behind it. Emergency rooms see these. They are hand, wrist, face and teeth injuries. People use screwdrivers and rebar because that is what is in the garage, and that is how most of it happens.

Both springs get replaced, not just the broken one

Both springs went on the same day and have taken the exact same number of cycles. When one hits the end, the other is right behind it. Beyond that, springs get sized as a matched pair against the door weight, so a new one working next to a fatigued one puts uneven torque across the shaft and the door never balances properly through its travel. Two service calls also cost more than one. This is not an upsell, it is the reason you are not calling us again in four months.

Sizing is measuring, not eyeballing

A torsion spring is defined by four things: wire diameter, inside diameter, length, and which way it winds. Those decide how much torque you get per turn. Picking the replacement means knowing what the door weighs, either by putting it on a scale with the springs off or by calculating from the panel construction and hardware. Too light a spring and the door stays heavy at the floor and burns through cycles fast. Too heavy and the door wants to fly open and the opener fights it all the way down. Both feel more or less fine on day one. Both cut the life of everything they are bolted to.

Broken Spring Replacement for River Oaks homes

A small post-war city along the Trinity River where 1940s-50s homes have narrow detached or single attached garages, and river-bottom humidity accelerates hardware corrosion.

Our route through River Oaks takes in 76114.

Anywhere around Trinity Trails is a short run for us.

River Oaks sits in Tarrant County with a population of about 7,505.

Please do not attempt this one yourself

That spring is still loaded even with the door down. People get badly hurt trying to unwind one with the wrong tools. Leave the door shut, do not pull the release, and call us.

What you are probably seeing

  • Top panel flexes or bends when the opener pulls on it.
  • Cables have gone slack or jumped off the drums.
  • Gaps between coils on a spring that has not broken yet, or rust pits in the coil.
  • A loud bang from the garage, and the door worked fine right up until then.
  • A two to three inch gap in the coil of the spring above the door.

River Oaks service

Call (214) 831-2545 or request a visit.

The visit

How a River Oaks call runs

  1. Confirm it and secure the door

    We find which spring broke, check whether the other one is still loaded, and clamp or block the door so it cannot move while we work. Opener stays disconnected the whole time.

  2. Measure the door and the old springs

    Wire diameter, inside diameter, length and wind direction come off the existing springs, and we establish what the door weighs. That decides the replacement. Not a visual match.

  3. Unwind and strip it

    Any leftover tension comes off with proper winding bars, cables come off the drums, old springs come off the shaft. We check the bearings, drums and shaft while we can actually see them.

  4. New pair, wound to the right turn count

    Both springs go on. Cables get set in the drums with equal tension so the door lifts square. Springs get wound to the turns this door needs, not to a default number.

  5. Balance by hand, then reset the opener

    Door gets lifted by hand and checked at several heights to make sure it holds position. Then the opener goes back on, travel and force get reset, and we test the safety reverse.

On the job

Broken Spring Replacement in the field

Questions

Broken Spring Replacement in River Oaks

Can I replace a torsion spring myself?

No. That is the one flat no on this whole site. It takes correctly sized steel winding bars, properly seated set screws, and a stance that keeps your body out of the arc of those bars. Improvised tools slipping under that kind of torque send people to the emergency room every year. Almost everything else on a garage door is fair game for a handy person. This is not.

Why do both springs have to go?

Same install date, same cycle count, so the second one is close behind the first. And springs get sized as a pair against the door weight, so a new one next to an old one never balances the door right through its travel. Doing it once costs less than doing it twice.

How long will the new springs last?

Take the cycle rating and divide by how many times a day you open the door. A standard 10,000 cycle spring is four to five years at six openings a day, or about fourteen years at two. If your house is on the heavy end, ask about high cycle springs at 20,000 or more. The price difference is small next to a second replacement.

Did I break it?

No. Springs fail from metal fatigue after a counted number of cycles, and they usually go on a cold morning because the steel is less forgiving then. The two things that actually shorten spring life are a spring undersized for the door at install and rust pitting on the coil. Neither one is about how you use the door.

Do you have springs on the truck?

The common residential wire sizes and lengths, yes, so most jobs get done on the first visit. Unusual sizes, very heavy custom doors, and some high cycle setups occasionally have to be ordered. If yours is one of those, you hear it at the diagnosis, not later.

Need this handled today?

Broken Spring Replacement in River Oaks and across Tarrant County.

Call Now Book